Nylon 6
Nylon 6 also known as Polyamide, is characterized by a combination of high strength, toughness and abrasion resistance and is ranked as an Engineering Plastic. This is because of its unique balance of mechanical, thermal, frictional and chemical properties. Nylon behaves in a predictable, reproducible manner under load and in known environments. Engineers and designers are looking to nylon as a substitute for design material such as phosphor bronze, gunmetal, cast iron, copper, aluminium and the entire family of steels.

Nylon is well accepted for several engineering applications. It is tough and hard, with good mechanical properties, high resistance to abrasion and impact and low friction properties.

Extruded Rods:
3mm to 9" diameter in standard lengths of 300mm, 1000mm, 4 ft., bigger cut to size & roll lengths.

Extruded Square Rods:
3/4" to 3" square (across flat) in standard 300mm, 1000mm, 4 ft., and non-standard lengths.

Extruded Sheets & Flat Strips:
0.2mm to 70mm thickness in width 300mm to 1000mm in roll length & ct to length up to 3000mm.

Top 

Nylon 66
Nylon 66 material bears higher mechanical strength, stiffness, hardness, toughness, heat and excellent wear resistance than Nylon "6". Nylon 66 has the highest melting point & it is the strongest and the most rigid of all unmodified nylons. It also has good sliding properties; better creep resistance but its impact strength and mechanical damping ability are reduced.

This product also has outstanding resistance to alkalies and organic materials, as well as good electrical insulating characteristics.

Modified & specialty grades are offered for defined industrial applications.

Rods: 6mm to 200mm diameter in 300mm, 1000mm & bigger lengths.

Flats: Small sized sheets & flats are produced against specific orders only.

Tubes & Hollow Rods can be offered on request subject to quantity.

Top 

Cast Nylon 6 (Polyamide - Nylon 6 )
Cast Nylon 6 (Polyamide - Nylon 6 ) is a high molecular thermoplastic material, which is produced by the active anionic polymerization of lactams. In the pressure less casting process the monomerous meltist poured into moulds and controlled by chemical reaction, is polymerized directly into semi-finished products or shaped cast pieces. Big sized sheets, rods & rings can be produced versus the extrusion process. The monomer casting process constitutes a considerable improvement in casting technology as compared to the normal extruded or injection molding method and it is particularly significant in terms of materials performance. In addition to this the properties and characteristics are accentuated by means of modification, special settings and additives.

Cast Nylon type 6 possesses very high molecular weight & crystallinity percentage. As a result, it has high tensile & compressive strength, modulus of elasticity, hardness; wear resistance, heat deflection temperature, resistance to solvents, excellent dimensional stability, low water absorption and low creep properties.

Cast Nylon Rods:
20mm to 500mm diameter in standard 300mm length, non-standard lengths up to 1000mm.

Cast Nylon Tubes & Pipes:
- 50x20 to 350x300 in standard lengths of 500mm & 1000mm.
- ODXID: 350x300 to 2200xVariable ID.

Cast Nylon Sheets:
6mm to 100mm thickness in 1000mm width & lengths of 1000mm & 2000mm.

Cast Nylon Squares:
25x25 to 150x150 in standard 300mm up to 1000mm lengths.

Top 

Polyacetal (Polyoxymethylene - POM)
Polyacetal (Polyoxymethylene - POM) is a widely used crystalline engineering thermoplastic popularly known as Delrin® which is a homopolymer Polyacetal which exhibits slightly different characteristics in copolymer grades. Polyacetal is characterized as having an excellent combination of physical properties that makes it suitable for numerous industrial applications.

Polyacetal has the following characteristics:

Polyacetal is used in many static & dynamic industrial applications replacing materials like; steel brass, bronze, copper and aluminium. Polyacetal have improved part life because of; better wear, more chemical and corrosion resistance. These materials reduce factory noise and will reduce or eliminate the need for lubricants.

Polyacetal can be used in applications such as; Gears, Bushings, Bearings, Rollers, Timing Screws, manifolds, Valves and Valve Bodies, Washers, Wear Pads, and many industrial machine parts.

Polyacetal Rods:
1/4" to 8" diameter in standard lengths of 300mm, up to 5 ft.

Polyacetal Sheets & Flat Strips:
6mm to 80mm in standard widths up to 300mm, 600mm, 1000mm in lengths of 1000mm, 4 ft., 2000mm.

Polyacetal Square Rods:
3/4" to 3" square (across flat) in 300mm, 1000mm & 4 ft. lengths.

Top 

Polypropylene (PP)
Polypropylene (PP) is light, strong, having resistance to chemicals and with a low friction surface, all of which make it ideal as a replacement for wood or metal which are the materials traditionally used. PP is a high corrosion resistant material, which exhibits excellent tensile strength and stiffness at elevated temperatures.

Homopolymer Polypropylene is harder, possesses excellent resistance to organic solvents and degreasing agent as well as electrolytic attack. Compared to low or high-density polyethylene, it has lower impact strength but superior working temperature and tensile strength.

Copolymer Polypropylene is harder than HDPE and likely to show good properties in lower temperatures. Copolymers have better impact strength, are good at lower temperatures than homopolymer & exhibit slight fall in other properties. Copolymer sheets are suitable for vacuum/ thermo-forming and mechanical fabrications.

Applications:

PP & HDPE Extruded Sheets:
0.7mm to 70mm in width 1000mm, 1220mm, 1250mm, 1500mm & lengths 2000mm, up to 3000mm, smaller thicknesses in roll lengths.

PP Extruded Rods:
1/2" to 10" diameter in standard lengths of 300mm & 1000mm.

PP Extruded Square Rods:
1" to 3" square (across flat) in standard lengths up to 4 ft.

PP Pipes & Tubes:
PP Homopolymer (PP-H), PP-Copolymer (PP-C) & PP- Random Copolymer (PP-R) for liquid & Solid Conveying, Transportation of Acids & Alkalies, Drainage Systems, Industrial Pipes & Hot Water supply for Sanitary installations.

PP Glass Laminated Pipe:
(PPGL) pipes for corrosive & pressure resistance applications..

PP Tubing:
Tubing for five retardent applications.

PP Fittings:
Stub End, Bend, Reducer TEE.

HDPE & Pipes:
HDPE High Density Polyethylene (HDPE) fluid pipes in PE 63, PE 80 & PE 100 grades for water, chemical Watse / Sewage / Efficient conveyance applications from 20mm OD onwards upto 560mm OD. HDPE Fabricated, Molded & Compression fittings.

Compression Molded Sheets:
10mm to 70mm thickness in widths 1000mm & 1250mm with lengths 1000mm & multiple thereof.

Thin Polypropylene sheets are used for Office Stationary Files, Folders & Bags. Corona treatment for printing on PP sheets is also offered.

Size: 0.5-2.0mm thickness up to 1000mm wide in roll length / cut-to-length.

Surface finish:
Oblique line (cross line), Semi Mate, Mate, Self Emboss, Orange Peel, Gloss.

Polypropylene Corrugated Sheets for packaging & printing are also offered in standard colours & sheet sizes. Polypropylene Welding Rods are used for welding PP tanks, liners, duct & many vessels. The available sizes are 3 & 5mm round rods in a handy spool between 1 to 2 Kg. The standard colours offered are White, Gray & Simona Gray.

Top 

HDPE
HDPE High Density Polyethylene is a polyolefin, which shows good low temperature impact resistance & excellent chemical resistance. It has lower stiffness compared to Polypropylene and does not show absorb moisture.

Used in different applications includes: chemical, food processing, pipe and pipefittings for water transportation, card-cans, UV protected panels, etc. A good market for HDPE sheet is for thermoformable products.

Top 

Cast Polyurethanes
Cast Polyurethanes are cost effective and dependable elastomers that combine the performance advantages of engineering plastics, metals and ceramics along with the resiliency and flexibility of rubber. These are internationally popular for their high load bearing capacity, high impact strength, high abrasion resistance, high resilience and excellent resistance to oil and grease.

The applications of polyurethanes include where the actions of sliding, bearing, stripping, forming, damping, cushioning, resting or rolling are involved.

For optimum performance, better results and longer life, selection of appropriate grades is important. These can be formulated with permutation & combination of selective chemicals & additives.

Cast Polyurethanes have unlimited running applications & a huge replacement market is waiting to turn on.

Applications:
Pads: Abrasion Resistant Linings, Gear Seals, Jigs & Fixtures, Mallets, Punch-strippers, Screens, Spacers, Rollers & Sleeves, Suspension Bushes, Scrapper Blades, Wheels, Wear Parts etc.

Cast Polyurethane Rods:
10mm to 200mm diameter in standard 300mm & bigger lengths.

Cast Polyurethane Hollow Rods:
ODXID: 20x08 to 200x180 (in mm) in standard 300mm lengths.

Cast Polyurethane Sheets:
1mm to 100mm in widths of 300mm, 500mm, 600mm & 1000mm upto1000mm lengths.

Other non standard sizes upon request.

Molded Components: Semi-finished & finished molded parts are produced against approved part samples and drawings subject to MOQ.

Top 

Thermoplastic Urethane (TPU)
Thermoplastic Urethane (TPU) results from copolymerization of two or more monomers. One monomer is used to provide the hard, crystalline features, whereas the other monomer produces the soft, amorphous features. Combined these form a thermoplastic material that exhibits properties similar to the hard, vulcanized elastomers.

Because of its toughness and versatility, as well as a generally higher price tag than other TPEs, urethane is typically used for parts requiring a high level of performance. These applications frequently demand a flexible material with a high degree of flex resistance, wearability, and durability. Particularly at lower temperatures, other materials do not provide this combination of properties.

Properties:

Applications: Automotive industry, building industry, medical industry, industrial equipments, sports & leisure industry, textile & garments industry, other general industry

Products:

Top 

Next »